產品分類/ Products
- HTA8127 內置升壓的77W單體聲D類音頻功放
- HT517 3.2W高性能數字單聲道D類音頻功率放大器
- HTA8128 內置升壓的60W立體聲D類音頻功放
- AU6815 集成音頻 DSP 的 2×25W 數字型 C
- HTN78A3 6V~140V輸入，3A實地異步降壓變換器
- HT81297 18W內置升壓單聲道D類音頻功放
- HT337B 120W 單聲道D類音頻功放
- NS2583 同步升壓型 2A 雙節鋰電池充電管理 IC
- NLC47022帶NTC功能和電量均衡功能電流2A 5V異
- PT2027 單觸控雙輸出 LED 調光 IC
- AU6815P 集成音頻 DSP 的 2 × 32W 數字
- HT316C兼容HT326C防破音功能免電感濾波2×20WD
- HT3386兼容TPA3118 2×50W D類立體聲音頻功放
- NS8220 300mW 雙聲道耳機音頻放大器
低噪聲運算放大器
產品名稱：AXOP39061 25MHz RRIO Operational Amplifiers(Single)
型號： AXOP39061
產片介紹：Excellent THD+N 100dB Excellent SNR 110dB Rail-to-rail input and output Low input offset voltage: ±0 5mV typ Unity-gain bandwidth: 25MHz Low quiescent current: 800μA typ Operational at supply voltages as low as 1 5V Easier to stabilize with higher capacitive load due to resistive open-loop output impedance
產片介紹：Excellent THD+N 100dB Excellent SNR 110dB Rail-to-rail input and output Low input offset voltage: ±0 5mV typ Unity-gain bandwidth: 25MHz Low quiescent current: 800μA typ Operational at supply voltages as low as 1 5V Easier to stabilize with higher capacitive load due to resistive open-loop output impedance
┄┄┄詳細介紹┄┄┄
Description
The AXOP39061 is a single channel low voltage (1.5V to 5.5V) operational amplifiers (opamps) with rail.to-rail
input and output swing capabilities. These devices are very suitable for applications where lowvoltage operation,
a small footprint, and high capacitive load drive are required.
Features
? Excellent THD+N 100dB
? Excellent SNR 110dB
? Rail-to-rail input and output
? Low input offset voltage: +0.5mV typ
? Unity-gain bandwidth: 25MHz
? Low quiescent current: 800μA typ
? Operational at supply voltages as low as 1.5V
? Excellent SNR 110dB
? Rail-to-rail input and output
? Low input offset voltage: +0.5mV typ
? Unity-gain bandwidth: 25MHz
? Low quiescent current: 800μA typ
? Operational at supply voltages as low as 1.5V
? Easier to stabilize with higher capacitive load due to resistive open-loop output impedance
Applications
? Infotainment system
? HVAC: heating, ventilating, and air conditioning
? Motor control
? Wearable devices
? Sensor signal conditioning
? Power modules
? Active filters
? Motor control
? Wearable devices
? Sensor signal conditioning
? Power modules
? Active filters
1 Block Diagram and Application Circuit
Figure 1 Block Diagram
Figure 2 Typical Application Circuit (Stereo Sound Input Amplifier)
2 Pin Description
2.1 AXOP39061A/B Pinouts
2.1 AXOP39061A/B Pinouts
3 Electrical Specifications
3.1 Absolute Maximum Ratings
3.1 Absolute Maximum Ratings
3.4 Electrical Characteristics
For Vs = (V+)- (V) = 5V at Ta = 25°C, RL = 10kΩ connected to Vs/2, Vcm = Vs/2, and Vout =Vs/2
For Vs = (V+)- (V) = 5V at Ta = 25°C, RL = 10kΩ connected to Vs/2, Vcm = Vs/2, and Vout =Vs/2
(unless otherwise noted).
Table 5 Electrical Characteristics
4 Functional Description
4.1 Overview
4.1 Overview
The AXOP39061 device is a low power, rail-to-rail input and output opamp. The deviceoperates from
1.5V to 5.5V, is unity gain stable, and designed for a wide range of applications and used in virtually any
single supply application.
4.2 Rail to Rail input
The input common mode voltage range of the AXOP39061 extends 100mV beyond the supplyrails
for the full supply voltage range of 1.5V to 5.5V. This performance is achieved with acomplementary
input stage: a N-channel input differential pair in parallel with a P-channeldifferential pair, as shown
in Figure 1. The N-channel pair is active for input voltages close tothe positive rail, typically (V+)-1.4V
to 200mV above the positive supply, whereas the P.channel pair is active for inputs from 200mV below
the negative supply to approximately (V+)1.4V, There is a transition region, in which both pairs are on,
Within this transition region.PSRR, CMRR, offset voltage, offset drift, and THD can degrade compared
to device operationoutside this region.
4.3 Rail to Rail Output
Designed as a low power, low voltage operational amplifier, the AXOP39061 delivers a robustoutput drive
capability, A class AB output stage with common source Mosfets achieves full rail-.to-rail output swing
capability. For resistive loads of 10kQ, the output swings to within 10mV(typ)of either supply rail, regardless
of the applied power supply voltage. Different loadconditions change the ability of the amplifier to swing
close to the rails.
4.4 Overload Recovery
Overload recovery is defined as the time required for the opamp output to recover from asaturated state
to a linear state. The output devices of the opamp enter a saturation regionwhen the output voltage exceeds
the rated operating voltage, because of the high input voltageor the high gain. After the device enters the
saturation region, the charge carriers in the outputdevices require time to return to the linear state. After the
charge carriers return to the linealstate. the device begins to slew at the specified slew rate. The overload
recovery time for theAXOP39061 is approximately 300ns.
4.5 EMI Rejection
The AXOP3906x uses integrated electromagnetic interference (EMl) filtering to reduce theeffects of EMl from
sources such as wireless communications and densely populated boardswith a mix of analog signal chain and
digital components.
上一篇：GS8721/8722/8724 11MHZ CMOS Rail-to-Rail IO Opamps
下一篇：AXOP39062/4/S 25MHz RRlO Operational Amplifiers(Dual/Quad)
